Licensing Requirement / Applications
The licensing requirements for harbour craft, including applications that may be needed.
Harbour craft must meet the requirements specified here. Changes to the craft may also require applications to be made.
Carriage of passengers or persons on a harbour craft
“Passenger” means every person on board other than:
- the master and members of the crew, or other persons employed or engaged on board the vessel; and
- a child under one year of age
Gross tonnage of vessel
The Gross Tonnage (GT) of a vessel is one of the bases for charging the licence fees and the port dues. Measure the gross tonnage by the formula [ GT = Length x Breadth x Depth x 0.2823 ] if a vessel:
- is not registered in an Port of Registry; or
- is not issued with any approved Tonnage Certificate
See the rates of payment of fees and dues for the various tonnage, types and classes of crafts.
Mooring or storage base
The MPA Port Regulations do not allow any vessel to:
- anchor, moor, lie or loiter in a way that obstruct the approach of other vessels to any anchorage, wharf or landing place;
- anchor in any fairway or lie in any position that obstruct a fairway; or
- beach within the port without the prior written permission from the Port Master
We therefore advise owners and operators to ensure that their vessels are properly moored/stored at designated or approved places when they are not in use. Find a suitable mooring or storage base before applying for a licence.
Inspection of the vessel
Every vessel should pass a compulsory inspection of her hull, equipment and appliances for the licensing as a harbour craft and thereafter every 12 months before its licence is renewed. Harbour crafts issued with valid statutory safety certificates by MPA’s Shipping Division or any of the recognised Classification Societies will be exempted from these inspections when they renew their licences.
a. Arranging for inspection
Arrange with the One-Stop Document Centre (OSDC) for the place, date and time of the inspection in person at least one week in advance.
- See the list of designated inspection sites and schedule
An applicant may request to conduct an inspection for the craft at an alternate site if it cannot be at a designated site due to draught, size constraint or other valid reasons. The OSDC decides on the acceptance of the alternative inspection site subject to the availability of a Port Inspector.
- See the inspection fee (under rates of payment of fees and dues)
The MPA reserves the right to change the inspection timeslot without prior notice.
b. Passing the inspection
The applicant will receive a Craft Inspection Report once the craft passes the inspection. He must make payment for the necessary dues and fees with the report within seven (7) days from the date of inspection. Refer to the Table on Dues and Fees for Licensing of Harbour Craft. Thereafter, the applicant will receive a craft licence certificate.
c. Cancellation or change of appointment for inspection
The applicant will have his inspection fee forfeited if he fails to turn up or fails to notify OSDC of any cancellation / change of appointment one working day before the inspection.
Display of licence number
The OSDC assigns a Craft Licence Number on receipt of the relevant documents. The licence number shall be:
- Carved-on, cut-in, or centred punched into the main beam of the vessel;
- Painted on each side of the bow and on every portable item of life-saving and fire-fighting appliances against a contrasting background; and
- Kept legible and visible at all times
The minimum height, breadth and thickness of each letter/number for each of the bow on a craft shall be as follows:
|LETTERS AND NUMBERS DIMENSION|
|Length of vessel||Height||Breadth||Thickness|
|Under 5 metres||10 cm||7 cm||2 cm|
|Between 5 and 20 metres||20 cm||15 cm||4 cm|
|Above 20 metres||30 cm||20 cm||5 cm|
|DISPLAY REQUIREMENT||DIMENSIONS OF THE LICENCE NUMBERS|
|SA, SP, Wooden SB, Wooden ST &Wooden SR||Harbour craft licence numbers to be mounted on the rooftop of the wheelhouse in an upright/horizontal position where the licence numbers could best be seen on both port and starboard sides.||Licence number to be painted at least 15 cm in height, 9 cm in breadth and 2.5 cm in thickness against a contrasting background.|
|Steel SB,Steel SR & Steel SC, Steel ST.||As above.||Licence number to be painted at least 30 cm in height, 21 cm in breadth and 5 cm in thickness against a contrasting background.|
|Wooden SC with canvas awnings||Harbour craft licence numbers to be painted on the canvas awnings above their normal “rolled-up” position.||Licence number to be painted at least 15 cm in height, 9 cm in breadth and 2.5 cm in thickness against a contrasting background.|
Renewal of craft licence
Renew the harbour craft licence before the licence expiry date. It is an offence to operate a craft without a valid harbour craft licence.
The owner has to do the following for licence renewal:
a. Pay the dues and fees. An owner will receive a Late Renewal Fee for payment received after the expiry date;
b. Arrange for the inspection of the vessel with OSDC before the expiry date of the craft licence; and
c. Submit the documents required for the renewal of the craft licence.
Medisave for Self-Employed Scheme
Self-employed applicants must ensure that they have paid up their medisave liabilities or have arranged for payment by instalment. For more information on the Medisave for the Self-Employed Scheme or to check the Medisave payment status for licence application or renewal, please logon to the CPF website at www.cpf.gov.sg.
Owners of harbour craft exempted from inspection shall ensure that their statutory safety certificates / documents remain valid throughout the duration of the licence.
Display of the craft licence certificate
Display the craft licence in a conspicuous place on board at all times. The Port Master, his representative or any police officer may demand to see the certificate.
Change of licensed harbour craft particulars
Report any changes of licensed craft particulars to OSDC within 7 days. The OSDC will update the particulars and issue a new craft licence certificate. You will find the types of change and the requirements of submission shown below:
a. Change of ownership
Unless the transfer of ownership is effected in OSDC, the previous owner will be held responsible for every violation of Regulations, and for all dues and fees payment for the vessel. The documents required for the change of ownership are as follows:
- NRICs of both buyer and seller or latest information printout from ACRA for company owned;
- Application Form (PM74) duly completed and signed by the new owner;
- New insurance policy to cover the new owner;
- Bill of Sale bearing both purchaser’s and seller’s acknowledgement;
- Original craft licence certificate;
- Manning licences of the minimum crew; and
- Mooring letter for confirmation of mooring/storage base of craft, if applicable
b. Change of gross tonnage, dimension or usage of vessel
The Port Master must first approve to any conversion work. The owner must perform the following upon approval or completion of the alteration:
- Submit the original craft licence certificate;
- Duly complete and submit the Application Form (PM74);
- Make arrangement for the inspection of the craft in accordance with the section on inspection of the vessel;
- Pay the Inspection Fee and any other dues or fees;
- Pay any additional dues and fees for the difference if there is an increase in GT or higher rate of licence
c. Change of propelling machinery or manning particulars
- Return the original craft licence certificate for amendment;
- Submit documentary proof on the change(s), e.g. new engine receipt/invoice or manning licences, etc.
- Make arrangement for the in accordance with the section on inspection of the vessel.
- Pay the Inspection Fee.
Registration of lien
The mortgagee or creditors of the craft subjected to the terms and conditions of a Mortgage Deed, Hire Purchase Agreement, Financing, Leasing and other financial arrangements may apply to OSDC for the endorsement of such instruments. The Craft Register and craft licence certificate will reflect such endorsements.
The Mortgagee or Creditors need to do the following for application:
- Submit a letter stating the request;
- Submit 3 sets of the Mortgage Deed/Hire-Purchase or Lease Agreement, etc; and
- Pay the Mortgage Registration Fee)
The OSDC will issue a craft licence certificate upon registration. It would then be the duty of the Mortgagee or Creditors to inform OSDC in writing of the eventual discharge of the Mortgage/Agreement, or of any Notice of Possession/Seizure issued for the craft. When the Mortgage/Agreement is discharged, the craft licence certificate must again be submitted to OSDC for updating.
Plying limits and craft leaving port
Harbour craft licences are issued strictly for the use of the vessel within the port limits of Singapore or places within the port limit as stipulated in the craft licence certificate.
Every harbour craft proceeding outside Port Limits must possess a valid port clearance certificate.
Cancellation of craft licence
Notify the Port Master in writing to cancel a craft licence. Use any of the following procedures to cancel the licence:
Apply for a Lay-Up Permit if a vessel is to be laid-up. The owner of a vessel must submit a letter issued by the owner or manager of such premises to confirm the authorisation of the vessel’s laying up position if the vessel is to be laid up on private land and clear of the port water at all heights of tide. The craft may require an inspection.
Inspection Fees are payable in accordance with the rates set out.
Apply for a Break-Up Permit if the vessel is to be broken-up. In addition, the owner should arrange with the OSDC to conduct a break-up inspection and a post-break-up inspection immediately after the vessel is completely broken up to ensure that the site is clear of debris.
Inspection Fees are payable in accordance with the rates set out.
The OSDC accepts photographs as evidence of the disposal / break-up of the harbour craft. Accompany the photographs with an official letter from the shipyard / shipbreaker confirming that the craft had been broken-up on a stated date within their premises.
c. Left port or shipped out
Submit to the OSDC a photocopy of the port clearance certificate, Export Permit issued or any documentary evidence of a vessel that has left the port for good or shipped out to have the licence cancelled.
d. Lost or missing
The owner shall submit a copy of the Report lodged with the Police if the vessel is lost or missing.
e. Damage due to incident or other accident
The owner, master or person-in-charge of the vessel shall submit a full written report to the Port Master within 24 hours of the accident or incident, and surrender the craft licence certificate to the Port Master. The report should state:
- the circumstances leading to the accident or occurrence;
- the extent of damage to his vessel, the extent of damage to third parties (if any); and
- whether any injury or loss of life was caused
Radio communication requirements for licensed harbour craft
Harbour craft that meet the requirements below must have a Radiotelephone that is capable of operating in the International Maritime Mobile VHF Radio Communication Service in the 156-174 MHz Band on Channels 7, 12, 18, 20, 21 and 22.
- Self-propelled vessel exceeding 300 GT;
- Tugboat engaged in towing where the combined GT of the tugboat and the vessel that is being towed exceeds 300;
- Port Limit Tanker; and
- Port Limit Passenger Vessel
The Radiotelephone shall at all times be maintained in effective working condition and shall be available for operation on the navigational bridge of the vessel.
Exclusion under the prevention of pollution of the Sea (Air) Regulations 2005
For a ship that is solely engaged in voyages within Singapore waters:
- Regulation 13(1)(a) will not apply to any diesel engine installed on a ship constructed or undergone a major conversion before 19 May 2005. This is in accordance to the First Schedule of the PPS (Air) Regulations 2005.
- Regulation 16(2)(a) will not apply to any incinerator installed on a ship before 19 May 2005 according to Regulation 16 (2)(b) of the First Schedule of the PPS (Air) Regulations 2005.
Harbour Craft Transponder System (HARTS)
Owners, masters or persons-in-charge should install all mechanically propelled harbour crafts with the HARTS apart from crafts fitted with Automated Identification Systems (AIS). See more details on HARTS.
Navigational lights carried by every harbour craft
|TYPE OF VESSEL||Masthead Light||Starboard Sidelight||Port Sidelight||Sternlight||Anchor Light|
|Power- driven Vessel||2||-||1||1||2|
|50m and above|
|12m – 50m||1||1||1||1||1|
|Under 20m||1||May combined in one lantern||1||1|
|Under 12m||An round white light and sidelight||-||-|
|Length & Speed 7m and 7knots respectively||An all round white light ( if practicable, also exhibit sidelights)||-||-|
|20m & above||-||May combined in one lantern||1||1|
|Length under 7m||Electric Torch / Lantern showing a white light|
|Vessel under oars||Electric Torch / Lantern showing a white light|
|Vessel engaged in towing||3||1||1||1||1|
|All vessels engaging in towing operation (ST) should have a working yellow towing light on board and this light should be illuminated during the towing operation.|
Contact information and opening hours of OSDC
Contact information and opening hours of OSDC
MPA One-Stop-Document Centre (OSDC)
7A Keppel Road #01-26
Tanjong Pagar Complex
Tel No: (65) 6325 2374
Fax: (65) 6325 2376
Monday to Thursday - 8:00am to 5:30pm
Friday – 8:00am to 5:00pm
Closed on Saturdays, Sundays and Public Holidays
Closed for lunch from 1.00pm to 2.00pm on weekdays
- Renew their licences
- Inspection of the vessel
- Apply for a Lay-Up Permit
- Apply for a Break-Up Permit
- The rates of payment of fees and due
- The list of designated inspection sites and schedule
- Table on Dues and Fees for Licensing of Harbour Craft
- Application Form (PM74)
- Mortgage Registration Fee
- Inspection Fees
- Port Operations
- Vessel Traffic Information System
- Port Clearance Formalities
- Vessels arriving in Singapore
- Vessels departing from Singapore
- Applying for a Bunker Convention Certificate
- Dangerous Cargo and Hot Works
- Using Dispersants in Singapore Port Waters
- Preparation of Tankers for Gas-Free Inspection
- Advance Notice of Arrival/Loading Hazardous and Noxious Substances in Bulk
- Applying for Port Chemist to Perform Gas-Free Testing
- Declaring Dangerous Goods (DG)
- Using Anchorages to Carry Out Hot-Work Repair Onboard Vessels
- Berthing Tankers and Conventional Vessels Carrying Bulk Liquid Cargo at Approved Conventional Wharves
- Recognised Training Service Providers Providing Training for Shorebased Personnel Dealing with IMDG Cargoes
- Licensing of Craft
- Harbour Craft
- Pleasure Craft
- Launching a New Vessel in Port
- Laying Up a Vessel in Port
- Breaking Up a Vessel in Port
- Bidding for A Craft Licence Number
- Pilotage Service
- Pilotage Exemption
- Pilotage Guidelines
- Bunkering Services Providers
- Bunkering Standards
- Bunkering 101 Placards
- Accreditation Scheme
- Bunkering Licence Application Guidelines
- Licensing of Bunker Surveying Companies
- Bunkering Statistics
- Mass Flow Meter for Bunkering
- LNG Bunkering (Pilot Programme)
- Charts, Tidal Information, Aids to Navigation & Hydrography
- Port Security
- Port Infrastructure
- Application for Foreshore and Marine Development Projects
- Approval of Works and Operations in Port
- Port Marine Safety
- Guidelines for Vessels Intending to Carry Out Lowering or Launching of Conventional Lifeboat / Free Fall Lifeboat / Rescue Boat into The Water at Anchrages
- Search & Rescue
- FAQs to Implementation of SOLAS Regulations VI/2 on Verified Gross Mass of Containers
- Incident Investigation
- Circulars and Notices
- Recreation & Leisure
- Marina South Pier
- Leisure Boating
- Introduction to Pleasure Craft Licensing
- Application for A New Licence or Re-licensing
- Registration of Pleasure Craft
- Inspection of Craft
- Renewal of Craft Licence / Notification of Non-renewal
- Change of Particulars after Licensing
- Report of Loss, Accident or Cancellation
- Registration of Lien on Craft
- Additional requirements to carry more than 12 persons
- Information on Licensed Pleasure Craft in The Port
- Visiting Seafarers
- IMO Matters
- Tariffs and Charges
- Charges for Marine Services
- Fees Payable by the Owner Agent or Master of a Harbour Craft
- Fees Payable by the Owner Agent or Master of a Pleasure Craft
- Fees Payable by Bunker Craft Operator / Supplier
- Charges for Vessel Inspection
- Maritime Welfare Fees
- General Charges
- Charges for Shipping Division
- Charges for Training Courses/Examinations
- Maritime Legislation of Singapore
- Attorney-General Chambers’ public website
- Maritime and Port Authority of Singapore Act
- Merchant Shipping Act
- Maritime Labour Convention Act
- Prevention of Pollution of the Sea Act
- Merchant Shipping (Civil Liability and Compensation for Oil Pollution) Act
- Merchant Shipping (Civil Liability and Compensation for Bunker Oil Pollution) Act 2008
- Port State Control
- Port Statistics
- Safety at Sea